Leveling Saddles

[aicabsolut]

Yeah, that sounds like your seatpost. Some are infinitely adjustable. Some have little notches. It seems like you need to be in between 2 notches on yours to get the right fit with that saddle. There are a lot of seatposts that are smooth at the top clamp so you can put it wherever you want.

[Tokie]

The seatpost on my Trek is the easiest to adjust ever! It really makes a huge difference! tokie

[Miranda]

The seatpost on my Trek is the easiest to adjust ever! It really makes a huge difference! tokie

Thx Tokie...

As you know I have been saddle searching for a while. Part of this I just thought was the saddles. The SI slr lady is one of the few that's a pretty level saddle to start in design, and probably one reason why it has felt better to me than some of the rest... cuz I could actually get it in the correct position to ride it! Hmm, it makes me wonder now how many other saddles might have worked better for me if the leveling challenge didn't exists.

[indysteel]

Thx Tokie...

As you know I have been saddle searching for a while. Part of this I just thought was the saddles. The SI slr lady is one of the few that's a pretty level saddle to start in design, and probably one reason why it has felt better to me than some of the rest... cuz I could actually get it in the correct position to ride it! Hmm, it makes me wonder now how many other saddles might have worked better for me if the leveling challenge didn't exists.

Good point. When I first got my bike, I had a professional fitting and my fitter mounted my Terry Butterfly Tri Gel at the time, using a level. Sometime later, I replaced the saddle with a new Butterfly and installed it myself. I naively thought I could get it level pretty easily.

Wrong. Even with a level, I repeatedly tried and failed to get it level. All the while, my girly bits were very sore. I finally took it back to him and he was better able to mount it, but explained that my frustration was caused by the "knurls" or notches in my seatpost. I'm getting a new bike soon and will give a lot of thought to which seatpost to get. I definitely want one that's easier to adjust.

Good luck!

[aicabsolut]

You don't really need a carbon seatpost to help the ride. A carbon rear triangle on your bike would help more than the seatpost. Plenty of people run Al posts on carbon bikes for one reason or another. Carbon posts will be more expensive.

[OakLeaf]

My saddle does pretty well "as is," but when I had my fitting, my LBS mentioned the possibility of using a shim cut from a pop can to micro-adjust the level without replacing the seatpost. It would definitely take a lot of trial and error, but it's a cheap way to go. It would compress a lot less than tape or rubber.

Thomson seatposts are popular, and American Classic also has infinite adjustment.

[Miranda]

My saddle does pretty well "as is," but when I had my fitting, my LBS mentioned the possibility of using a shim cut from a pop can to micro-adjust the level without replacing the seatpost. It would definitely take a lot of trial and error, but it's a cheap way to go. It would compress a lot less than tape or rubber.

Thomson seatposts are popular, and American Classic also has infinite adjustment.

Thx OL... the Thompson looks nice. I would have never thought of the pop can shim.

I did try out my rubber shim today. I used a jar gripper piece out of my kitchen junk drawer. I only went around the neighborhood at a slow speed with no traffic. So, I felt ok about testing it.

At first, I was so happy. Without the groove issue, I got it to work! It leveled out beautifully. Instantly when I mounted to ride... Much better. But, it didn't stay that way. Lady bits started to get some pressure. When I got home, I thought I'm going to re-check the levelness. It shifted of course. Nose up (body weight on the back of the saddle).

Part of it I wonder if I didn't have it torqed tight enough? I didn't really want to on the short test ride to mark it up. But, I wonder with the single screw design, and one washer, in the oval slot... does that make it more prone to shift?

It would make sense I guess after looking at the other seat post, like the Thompson with a set of screws, vs my one.

[Miranda]

You don't really need a carbon seatpost to help the ride. A carbon rear triangle on your bike would help more than the seatpost. Plenty of people run Al posts on carbon bikes for one reason or another. Carbon posts will be more expensive.

OK, that's good to know. Sometimes I've had the experience in the lbs that the part ends up being the most expensive whatever it is. I wonder, do I really need that for more $ ? But, I do know certain things you get what you pay for. I'll have to geek it out a bit.

[Miranda]

... I'm getting a new bike soon and will give a lot of thought to which seatpost to get. I definitely want one that's easier to adjust.

OK, you just read my of earlier today. When I got my bike, I never really thought too much about my individual components design. It looked ok in "the bike package". While I still don't have it all nailed now, there are definately some things I know I want different. After this experience, I'm with ya... a post without this type adjustment factor for sure.

[Miranda]

Yeah, that sounds like your seatpost. Some are infinitely adjustable. Some have little notches. It seems like you need to be in between 2 notches on yours to get the right fit with that saddle. There are a lot of seatposts that are smooth at the top clamp so you can put it wherever you want.

YES... that is exactly what my seatpost clamp looks like. It has grippy grooves/notches in the clamps that resemble that of a plastic zip tie. I think when I go to torq down the tension, the nothes (if lined up on top of each other wrong, aka male to male pieces, vs female to male) slip... unleveling the saddle from where I had it originally.

My OCR1 is an aluminum frame, with carbon being only in the forks and seat post. When I got the bike as a new rider, it was plenty for my skills. Now, I want to upgrade to all carbon to smooth out the ride from the aluminum frame chatter. The carbon in the forks and seat post are suppose to be something in the current design that helps to smooth that out.

Hmm, obviously there are other seat post that might do it, but I wonder if some modification to what I have would do it...

OK, in reality, I'm assuming in this would not be "secure" on a ride, but I'm thinking about filling up the grooves in the clamp with tape, maybe a smooth rubber shim, *something* for a test. All I have on hand now is tape. Things like seat post rack clamps, handle bar light clamps, etc. come with rubber shims. That's sorta what my brain was thinking. Sure a shop could find me a carbon post without the groove issue (for a price, dunno what though).