Shifting without gear indicators

[maillotpois]

What does a gear indicator look like?

[OakLeaf]

What does a gear indicator look like?

For Shimano brifters, the flight deck computers have them:



For grip shifters, they can be stamped and painted on the clamp section:



Others?


Like most everyone else I go by feel ... but I probably don't pay as much attention as I ought to, because there are times I'm cross-chaining and don't realize I'm still in the big ring until I hear the noise of the chain complaining , and it can't be good for the shifter cable to keep trying to shift down when I'm already in my lowest gear. I do look down occasionally to see where I am.

[Crankin]

I did start riding on a hard tail mtb that had them, but it didn't take more than a few rides on a road bike to get the "learn by feel" thing. I do occasionally look down, and that's usually when I am in trouble!

[Catrin]

Thanks everyone, I wasn't sure if this was common or not as all of my bikes until this one has them. I still wish I could switch the triggers on my mtb to grips, but SRAM apparently is not making 10-speed grips...I REALLY like the micro-indexing on my left grip on the Gunnar.

I shift the rear by feel anyway, I mainly use the indicators on my other bikes to make certain I am in hard enough a gear when I move to the granny in front that I won't suddenly feel like I am free-wheeling. I can listen to see if I am cross-chaining until I get used to this. It is just really odd to look down and not see those indicators

[maillotpois]

Ah - thanks, Oak. Someone mentioned I probably have them on my MTB but it doesn't get ridden unless I am on vacation.

I go by feel/sound. Campy allows for small adjustments to the front derailleur and you just learn the sounds to know which way to adjust.

[sundial]

I have a gear indicator on my mtb and I don't look at it. I just go by feel and sometimes I am pleasantly surprised to find that I was in a harder gear when I finished the ride.

[Catrin]

A
I go by feel/sound. Campy allows for small adjustments to the front derailleur and you just learn the sounds to know which way to adjust.

My LHT has this, the Shimano triggers allow me to adjust the trim a bit on the FD but not much. I really like how the front X0 grip shifter on my Gunnar is micro-indexed so I have a lot more room for trim. Have I mentioned I REALLY like those grips?

I actually called SRAM this morning to find out if there are plans to make grips available for 10-speed. I guess they had decided not to do that, but they have had so many direct requests from consumers and bike stores that the customer service rep things that they will eventually be available The triggers are sweet, even with MY thumbs/hands, but I like the grips even better

[hulagirl]

When I got my first bike without indicators I was all in a panic. After about 6 months, I don't want to ever ride with indicators again. I find that you (general) spend wayyyy too much time trying to figure out where you are in gear, if it's right, oh no...should you shift? And not enough time looking where you are going and around in general.

Without indicators, I ride mostly by sound. And feel of course. But I can hear it when I'm getting to the cross-chain fine line of doom. And I can feel it on the legs when things are too hard or too easy. Best thing is I keep my eyes on the road and don't spend all that much time really caring what gear I'm in, just as long as I'm not ready to pass out or it's getting noisy.

[laura*]

I actually called SRAM this morning to find out if there are plans to make grips available for 10-speed. I guess they had decided not to do that, but they have had so many direct requests from consumers and bike stores that the customer service rep things that they will eventually be available

There might be a technical reason why 10 speed twist shifters might never be available: With twist shifters, the cable needs to be pulled in a circle with a diameter greater than the handlebar diameter. A decent angular separation between each gear might mean significant cable pull. I think this (and not precision shifting) is why SRAM went with their 1:1 derailleur ratio - and why Shimano, sticking to their 2:1 ratio, has never offered twist shifters.

SRAM and Shimano are both using a new different cable pull ratios for their 10 speed MTB derailleurs. Rumors place them somewhere between 1:1 and 2:1. It could be that neither brand will work nicely with twist shifters.