Shifting problem

[KnottedYet]

I really hope it isn't a bent sprocket - that sounds expensive

Naw. $20-$25.

[Catrin]

The crank teeth look fine - at least to my inexperienced eye they do.

I did note that for some reason the chain in the middle chain ring does rub the side of the FD quite a lot. I also noticed this happening whether I trimmed it or not. Perhaps it still isn't adjusted quite right?

[KnottedYet]

The crank teeth look fine - at least to my inexperienced eye they do.

I did note that for some reason the chain in the middle chain ring does rub the side of the FD quite a lot. I also noticed this happening whether I trimmed it or not. Perhaps it still isn't adjusted quite right?

Try moving it more. Two smidgens. Three smidgens. Four smidgens. Move the shifter enough that the cage is centered relative to the chain. (trimming it means centering it or at least moving it enough that the chain isn't hitting the side plates of the der cage) Play with it. Move the cage so the chain touches one side, then move the cage so it touches the other side. Get a feel for just how much you can move that cage within the arc around the middle chainring without actually shifting the chain to the next ring.

It's like doing the waltz with your shifter, derailleur, chainrings, and chain. Find their happy place, where they work together and keep the beat.

It could also be that the cage is set at a sharp angle to the chain line where you just can't trim it.

If you can't figure it out and do take it to the LBS, have them show you exactly what is going on and exactly how to fix it. Knowledge is power!

[Catrin]

Try moving it more. Two smidgens. Three smidgens. Four smidgens. Move the shifter enough that the cage is centered relative to the chain. (trimming it means centering it or at least moving it enough that the chain isn't hitting the side plates of the der cage)

It could also be that the cage is set at a sharp angle to the chain line where you just can't trim it.

If you can't figure it out and do take it to the LBS, have them show you exactly what is going on and exactly how to fix it. Knowledge is power!

It only allows me to move it one smidgen and the next one puts me onto the next ring - it is indexed only. I will ask for more information this week when I take my bike to get the new saddle. Last week they adjusted the location of the cage and also changed where the stops were?

At least I got to see what is actually happening and can have a better discussion about it. Thanks!

[KnottedYet]

Well, if they changed the cage angle, that could be the problem.

Make sure they show you what is up, and how to fix it yourself next time.

[Trek-chick]

I was having the same problem with my Trek 520 especially on the middle ring too. I had my LBS adjust the rear dérailleur and it fixed the problem for a while. It started happening again and I was about ready to take the bike in again. The bike is only 4 months old too.

I think I figured out my problem though...... I commute to work and ride 9 miles in really dusty conditions on an old railroad bed. My drivetrain was getting pretty dirty within just a few days time. I can even see a thin layer of dust on the bike when I get home.

Whenever my shifting starts getting rough, I started just giving the bike and especially drivetrain a thourough cleaning and re-lube and the problem ( for me ) goes away. I actually just ordered myself a set of full-fenders so, hopefully it will help protect my drivetrain from road dirt and grime. I think I need a better chain lube too. My LBS used White Lightning... Self cleaning wax lube.

[Catrin]

I was having the same problem with my Trek 520 especially on the middle ring too. I had my LBS adjust the rear dérailleur and it fixed the problem for a while. It started happening again and I was about ready to take the bike in again. The bike is only 4 months old too.

I think I figured out my problem though...... I commute to work and ride 9 miles in really dusty conditions on an old railroad bed. My drivetrain was getting pretty dirty within just a few days time. I can even see a thin layer of dust on the bike when I get home.

Whenever my shifting starts getting rough, I started just giving the bike and especially drivetrain a thourough cleaning and re-lube and the problem ( for me ) goes away. I actually just ordered myself a set of full-fenders so, hopefully it will help protect my drivetrain from road dirt and grime. I think I need a better chain lube too. My LBS used White Lightning... Self cleaning wax lube.

When I had my bike on my car's bike rack last night I noticed that the RD and some other places looked pretty dirty, perhaps this is a similar problem. I use Rock and Roll dry lube which is a good lube - but have been unsure how often to relube and how often to clean and relube. I am averaging 100 miles a week right now so perhaps this is a part of the equation as well. I had not thought about this.

I think a work stand would make it easier for me to clean