Taking off pedals

[lph]

That's right, pinkbikes, the righthand pedal loosens by turning the wrench counter-clockwise, the lefthand pedal loosens by turning the wrench clockwise, what I call "backwards" (the opposite of the pedalling direction). I have a Park Tool pedal spanner with a long handle, never had to stamp on that

[OakLeaf]

It takes a lot of leverage, and it looks like your multi-tool is probably pretty hard to get a good grip on. If you have a length of pipe that will slip over the end of it, try that to get a longer lever.

Honestly, most of the time I need DH's help to hold the other pedal (and when I don't, I worry that the pedals were loose ), even though I've got reasonable upper body strength and most of the experienced wrenches here will tell you I shouldn't need the help. I think some of it just depends on your frame, too, the size and geometry, how hard it is to reach through it and get a good angle on both pedals.

Then before you go to install the new pedals, put some anti-seize lubricant on the threads. If you've never done it before: use a very light coating - get a small dot of it on your finger (wearing thin gloves), smear it on the threads of the spindle, and use an old toothbrush to distribute it through the threads from inside to outside. Not so critical when it's a pedal and crankarm, obviously, but just a good habit to get into when you apply anti-seize.

[mariacycle]

Thanks everyone for the tool advice. i thankfully did know that the right/left pedal didn't both follow righty-tighty/lefty-loosey but I think my biggest obstacle is this short wrench with little leverage. My new pedals do come on very easily it's just a matter of getting these first ones off.

I'm at school and away from my LBS where the guys there seem to take pity on me and fix everything for free (they've given me tons of tuneups for free too, really great guys). I'm not sure whether it's worth coming to the LBS here (where people do seem pretty nice but obviously don't know me) since they'll probably charge a lot simply for loosening two pedals. Or... they'll look at me like I'm crazy for coming to the store just to do that. Am I crazy?

[OakLeaf]

Another set of arms is helpful. Calling your friend is probably a better idea than taking it to a LBS from which you didn't buy the pedals... You hold the opposite crankarm and let him reef on the pedal, or vice versa.

Just make sure whoever you call also knows that the right pedal is regular thread and the left pedal is reverse ("left-hand") threaded.

[Ered_Lithui]

Don't be embarrassed! And the big Park Tools pedal wrench is awesome, but even with it I've seen big tough mechanics slip a "cheater bar" over the end to get extra length and leverage. I'd just take it in to the LBS and explain that your tool's not doing the trick. I doubt they'd charge you for it.

Putting a little grease on the threads before putting the pedals on might help in future.

[Desert Tortoise]

Lph, when you said right hand pedal loosens counter-clockwise and left hand pedal loosens clockwise, is that with the bike upright or upside down (handle bars on the floor)?

(For some dumb reason I can't find how to copy a quote on here.)

Thanks!

[mariacycle]

upright bike in my limited experience with my dad's bike

[lph]

Lph, when you said right hand pedal loosens counter-clockwise and left hand pedal loosens clockwise, is that with the bike upright or upside down (handle bars on the floor)?

(For some dumb reason I can't find how to copy a quote on here.)

Thanks!

Oh, sorry! Bike upright. I have a work stand so I only work with it that way now.

[OakLeaf]

Unless it's Look pedals, or any other pedal that might fasten with a hex-head on the end of the spindle, in which case you're backwards ("tightening" direction to push the pedal outward and loosen it, and vice versa).

Just remember right-hand pedal is standard thread, left-hand pedal is reverse thread, then it won't matter what orientation you're looking at it from.