glove question

[shootingstar]

Just make sure when you try on gloves in the store, that they aren't totally snug or tight. Your hands expand when you get hot/very active. If you find you cannot take off your glove easily when you are hot, that's not necessarily a good thing.

Are you completely comfortable on your bike? Any neck/back pain? Any aches and pains that persist? Your arms in their most relaxed position while you are riding on your bike, should have a tiny natural bend at the elbow when riding easier parts of route. Not ramrod stiff straight.

And your handlebars and arm positioning, should be shoulder width.

Try to see when you ride along for awhile, to deliberately relax your arms...as a test, ride like ragdoll..

I have small hands, yet for the past few years I avoid XS gloves. If the glove design allows me, I will go up next size.

[babynoahsmom]

I had my bicycle fitted to me. I don't seem to have any other aches or pains. I do try to relax my arms every once in a while. I need to talk to the bike fitter at the shop about my problem. I bought one pair of "gel" gloves. I could not tell any difference with them.

[Cataboo]

gel gloves make my hands worse... I rip the gel out of my gloves.

if they're tight across the wrist it might hurt.

How much road feel do you get in your bike? If I get too many vibrations to my wrist... my hands go numb... if I bend my wrists back towards me at all, my hands go numb... so make sure when you're on your bike that your wrists end up being straight.... You can get gel padding to put under your handlebar tape (I don;t know if the dolce is a flat bar or not, but if it's dropped bars, gel padding helps)... If it's flat bars, you can get ergo grips.

You can get bar end plugs that go into your bar ends to dampen vibrations. I switched to carbon handlebars to minimize how much vibration I get in my wrists, but I know specialized has handlebars with zertz inserts that are also supposed to dampen vibrations...


How much weight are you putting on your wrists? You shouldn't be leaning forward onto them or putting weight on them, your core muscles in your back, etc. should be supporting your weight... if you're putting weight on them, concentrate on using your body to support your weight and not your wrists.

If you can see a bumpy section of road or a bump comping up, loosen your grip on the handlebars, sorta bend your elbows to dampen the amount of vibration that your wrists are going to absorb.

I hope one of these suggestions helps!

Definitely move your hands around as you're riding... don't have a death grip on your handlebars... move your hands to a different section of bar or different angle every so often...

[babynoahsmom]

Thanks! That is some terrific advice. I am riding this afternoon and I am going to try it out. I think I may be bending my wrists now that I think aobut it. I actually had gel tape put on my bars not long after I got her. I might need to think about the carbon upgrade if repositioning doesn't seem to help. I will lyk! Thanks again!

[fidlfreek]

Hey I was thinking that if you're coming from a mountain bike then maybe you're not taking full advantage of the myriad of hand positions open to road bikers. If you're not putting your hands in a different position every few minutes then maybe you're not moving them enough....I can think of at least 6 different options. On top, on the bend on top, on the shifters, on top of the shifters, in the drops, down at the end of the bar. I'm sure there are more...

Also, realize that if you go carbon bars then you're much much more likely to have to replace them after a crash because they're relatively fragile. And a minor crack can lead to catastrophic failure!

[Eden]

Do your gloves have a velcro wrist closure? - Don't close it... and definitely don't pull it tight. My fingers start to go to sleep even if I loosely close my gloves. Even a little pressure is enough to do it. Also as with saddles and chamois, more is often less. I prefer a pretty thinly padded glove - no bulky gel, super padded palms - just enough to protect my hands in case of a fall and prevent chafing. Highly padded gloves just increase the chance you'll get pressure in the wrong spots.

[tctrek]

I'm no expert, but I think hand numbness has less to do with your gloves and more to do with your hand/arm position. If you lean too much on your hands, whether you're on a bike or not, your hands/wrists will get tingly/numb. Of course, tight gloves could account for numbness, but I think form of your arms/hands has more to do with it. Make sense?

[Cataboo]

Also, realize that if you go carbon bars then you're much much more likely to have to replace them after a crash because they're relatively fragile. And a minor crack can lead to catastrophic failure!

I can't say I've had a crash on the carbon bars yet.... But I usually figure anything that makes my wrists happy so that I can ride without misery is worth it

[Miranda]

I can't remeber where I read this atm, but...

It was something about squishier (is that a word even lol) grips, wraps, etc. can aid in hand/wrist issues. Some study that was done on body mechanics. Basically, sub-consciously you grip the softer surface MORE in a effort to still keep a tight grip. The tigher you grip, the more work your hands are doing, more fatigue, stress etc.

I don't know what type of work you do for a living either, but I have some carpal tunnel issues. Just like my houses' allergery issues (acculative effect), the wrist issues can be acculative too w/use. Meaning if your wrists get a workout for 'work', then you work them more in your new road riding position... well, you get the idea I think.

My mtb rides are not as long as my road rides, and positioning is all over. Which you said positioning is part of it. But the repetative working of the muscles can aid in it. I specifically stretch my hands & wrists for riding like for my pc use. Even if not pc, things like holding a pen repeatedly, etc. can do it too. I think the stretching exercises helps.

FWIW. Good Luck.