terry precision

[surgtech1956]

Thanks, there's one on Ebay and looks in very good condition - its local pick up only, only about an hour from me - its a 1999 and the bid is at $179.

[surgtech1956]

KnottedYet - thanks so much for the forum link.

[KnottedYet]

Is this the bike?
http://cgi.ebay.com/STEAL-MY-BIKE-Te...QQcmdZViewItem

27.5 inch standover. Nice and small. It isn't too hard to get stuff for the 24 inch front wheel, either. Bar end shifters are nice (have 'em on my Surly).

I'd get it!

(well, *I* wouldn't get it, cuz I'm on the tall side, but YOU should get it!)

[Triskeliongirl]

I have two terry bikes with 24" front wheels. Getting wheels, tubes, and tires are no problem. The terry fit really works for my body (shorter upper body and arms with proportionally longer legs). As long as you don't mind the 7 spd rear, I would say go for it. You can still get 7 spd freewheels from Harris Cyclery. I looked at the listing and the condition looks terridic. Her older steel frames were very well made. In fact, I think all her steel frames are better than her current aluminum ones. Let us know if you get it! PM me later if you want advice on wheelsets, etc.

p.s. the listing says the model is the symetry, which is her entry level road bike. it is basically a 'sport bike' geometry, it should also have eyelets for a rack, and take tires up to 28c wide if its make like the more recent ones. fyi you can now get 24" tires in sizes from 23c to 32 c, not a lot of choice but what's out there is good quality and works well.

[surgtech1956]

Thanks girls. I think its looks in great shape. It looks like the color is silver. I think the size is right for me to - I'm 5'5" with about a 29" inseam and I think a little smaller bike will work for me better - I have a permanent knee problem(patella femoral joint) and need my seat up to make it easier on my patella. I'll keep you posted if I win the auction.

[Triskeliongirl]

Thanks girls. I think its looks in great shape. It looks like the color is silver. I think the size is right for me to - I'm 5'5" with about a 29" inseam and I think a little smaller bike will work for me better - I have a permanent knee problem(patella femoral joint) and need my seat up to make it easier on my patella. I'll keep you posted if I win the auction.

Actually, based on this info. I think it may be a size too small for you. I am 5'4" with a 30.5" cycling inseam, and the 19" frame fits me much better than the 17.5" frame (I own one of each). If your cycling inseam is really 29" though, the 17.5" one may be fine. Is 29" your pants inseam or cycling inseam. Cycling inseam is measured in bare feet, but pressing a book or something into your crotch and then marking on a wall the distance from your pubic bone to the ground.

You said its only an hour drive. Can you make an appt. to test ride say an hour before the auction closes, and then place your bid either on the sellers computer or your cell phone if you are happy with the ft?

p.s. if your cycling inseam is really 29" then this bike should be a good fit, as I have minimum clearnance on my 19" frame with a 30.5" inseam. 29" just seems small for your height.

[surgtech1956]

Let me see if I have this right. From the bottom of my foot(floor) to the crotch area is just almost 30 inches. I put a book - maybe too big of a book and it measured 26 inches. Does this sound right???

[KnottedYet]

Be sure to set the saddle back far enough that your knee is just *behind* the spindle at the forward horizontal pedal position. (ie: saddle low and back) That takes the stress off the patellar-femoral joint. And it's pretty darn comfy, too!

Standard fit is to have the knee at the spindle, but from a PT standpoint behind the spindle is kinder to a pat-fem issue. Get ahold of Andy Pruitt's book, and give a holler to the PT and PTAssts on the board if you need help.

I hope you "win" that Terry! Sweet bike!