Clicking in "easier" gears?

[bluerider]

After I bathed my bike last weekend, I am noticing she is clicking when I’m in the higher or “easier” gears? I’ve properly lubed her. I have a triple and the clicking is especially noticeable in the mid ring when I’m in the “easier” gears.

Once I shift down, it disappears. Do you know what the cause is and how do I go about fixing it?

I can bring it into the LBS but I feel like I’m there every weekend!!! I was there last weekend because I bent my front lever from a little fall. I’d like to try fixing my own problems or better yet, ask you ladies for advice!

[yellow]

Sounds like this is the perfect opportunity to learn how to adjust your derailleur (front)! (Probably just limit screws.) They do get out of adjustment over time. You only need two tools: a screwdriver and an allen wrench.

Another thing...the Shimano triples have the "trim" feature for the middle chainring. It's like a smidge of an adjustment on the front derailleur. You may just need to do the smidge shift up or down on the front. This was discussed here a while back.

If you do take it into the shop, have the techs show you how to adjust it. It's super easy and a really good thing to know how to do.

[bluerider]

Sounds like this is the perfect opportunity to learn how to adjust your derailleur (front)! (Probably just limit screws.) They do get out of adjustment over time. You only need two tools: a screwdriver and an allen wrench.

Another thing...the Shimano triples have the "trim" feature for the middle chainring. It's like a smidge of an adjustment on the front derailleur. You may just need to do the smidge shift up or down on the front. This was discussed here a while back.

If you do take it into the shop, have the techs show you how to adjust it. It's super easy and a really good thing to know how to do.

Thanks Yellow! Awesome links. I think that's what it is. At least I hope that's what it is. I've got a handy tool device thingy so it's time I start using it!

[Kimmyt]

Is your derailleur hitting the chain in these gears? It might need adjusted.

K.

doh, i was beat to it!

[DebW]

If the front derailleur needs adjusting, it's usually a scraping sound, not a clicking sound. Is the sound still present when you turn the crank by hand (on a work stand or with the bike upside down), or only under riding load? If the sound is there with the bike stationary, look to see if the chain is scraping the front derailleur or something else. If the rear derailleur is out of adjustment, the chain could be ticking a second sprocket. Another possibility is that the chain and or cogs are worn and need to be replaced. If the sound occurs on the cogs that your ride the most and the drivetrain is more than a couple years old, this is possible. Your LBS can quickly check chainwear or you can buy a chainchecker. Also, some people on this board have mentioned that using WhiteLightning lube on the chain has lead to drivetrain noise.

[bluerider]

If the front derailleur needs adjusting, it's usually a scraping sound, not a clicking sound. Is the sound still present when you turn the crank by hand (on a work stand or with the bike upside down), or only under riding load? If the sound is there with the bike stationary, look to see if the chain is scraping the front derailleur or something else. If the rear derailleur is out of adjustment, the chain could be ticking a second sprocket. Another possibility is that the chain and or cogs are worn and need to be replaced. If the sound occurs on the cogs that your ride the most and the drivetrain is more than a couple years old, this is possible. Your LBS can quickly check chainwear or you can buy a chainchecker. Also, some people on this board have mentioned that using WhiteLightning lube on the chain has lead to drivetrain noise.

Thanks DebW. It is a clicking and not scraping. At least I think it is. Yup the sound is still there when I hand crank it. I will take a closer look tonight. I think my chain should be okay as I replaced it about 2 months ago. It's just aggravating to listen to and to avoid it, I end up having to mash up hills!

[Grog]

Thanks DebW. It is a clicking and not scraping. At least I think it is. Yup the sound is still there when I hand crank it. I will take a closer look tonight. I think my chain should be okay as I replaced it about 2 months ago. It's just aggravating to listen to and to avoid it, I end up having to mash up hills!

If you changed only the chain and it had been worn out for a while, it could be the block (cassette) that's worn. These two usually wear out together.

I noticed there are two philosophies regarding chairn-wear in bike wrenches:

A (most common) - Change chain as soon as it's overextended to the 1.0 level (see chain-measure tool).

B (less common) - Don't chain chain until it starts skipping teeth on your cogs. Then change the chain AND the cassette.

My chain has been overextended for a while but it hasn't impaired the capacity of the bike to shift or anything yet. My mechanics wants to wait until it becomes a problem to change it. It helps that he sells me parts at cost. But now I'm starting to think that I might even have to change the cranks when that day comes and even at cost it's going to be expensive (Ultegra here).

[DebW]

My chain has been overextended for a while but it hasn't impaired the capacity of the bike to shift or anything yet. My mechanics wants to wait until it becomes a problem to change it. It helps that he sells me parts at cost. But now I'm starting to think that I might even have to change the cranks when that day comes and even at cost it's going to be expensive (Ultegra here).

When the chain gets stretched excessively (probably considerably greater than 1%) it doesn't fit the chainrings properly and you'll see a gap between the chain and the bottom of the teeth. This will wear the teeth into needle sharp points, and the chainrings (not the whole crank) will need to be replaced. I did this to my chainrings once. Not sure if it really happened because of chain wear of just a softish alloy in the Stronglight chainrings with lots of miles on it. And I've seen one other bike with a chain stretched to this extent. But I think it's pretty rare. I'd monitor the shape of your chainring teeth and whether the chain sits solidly at the bottom of the teeth. If you get worried, well, chains are much cheaper than chainrings.