gears

[sandy45]

ok i know this might sound stupid...but i have been biking for a year and half but have only be some what serious the last 6 months. i am getting more into dirt jumping now, which is fun. but DH sucks at explaining anything. so i am so confused on the gears. i have an 07 specialized hard rock sport. in the front i have 3 rings i normally stay in the middle. and in the back i have 8 rings. he keeps telling me go low or high and then gives me numbers. but then when i move to that number he gets pissed off and says i didnt listen...men ...anyway. i am trying to figure out what a low gear means...is it a small ring or a big one. then from there i will look at the numbers. when i was riding today...the second time....i was spinning like crazy in a 2 in the back. so what does that mean?

can anyone help?

[Grog]

I don't have a lot of time for a detailed explanation now, I'm sure others will, but I strongly suggest you put the bike on a stand or set it up in such a way that you can actually turn the cranks (with your hands) while standing besides it. Try changing gears in the front and back and see what happens, how much resistance you feel...

In my neck of the woods 'low gears' means easy gears (less resistance) and 'big gears' means lots of resistance.

[makbike]

Sandy:

I found it quite helpful to calculate my gear inches. Once I had them calculated I made a small gear chart and taped it to my top tube. I can quickly refer to it when looking for the gear to match my terrain, wind, etc.

Here is the formula for calculating gear inches:

Gear Inches = Rear Wheel Diameter x # of teeth on front chainring
# of teeth on rear cog

Here is what the range of gear inches is best used for:

20" steep hills with loaded bike
30" steep hills
40" somewhat steep hills
50" Moderate uphills
60" easy riding on flat ground or slight uphills
70" brisk riding on level ground
80" hard riding on level ground or slight downhills
90" sprinting on level ground or moderate downhills
100" somewhat steep downhills

on my bike the combination of small ring on the front chainring and small on cog on the rear gives me 100" - a very tough and big gear to push but it does come in handy for the long downhills. On the other hand the combination of frong chainring and large cog on the back gives me a 38" gear a very small gear and very easy so I use it on those tough climbs.

I hope this helps!

[BleeckerSt_Girl]

Sandy, here are some articles that talk about gear shifting:
http://sheldonbrown.com/gears.html
http://www.bicyclesouth.com/shifting.htm
http://bicycleuniverse.info/eqp/gears.html

[anakiwa]

Looking at it really simply-

Think about how many teeth you're moving in the front versus how many teeth you're moving in the back (to make the wheel turn).

In the front the small ring is the easier ring (low gear). With one turn of the pedals you aren't moving that many teeth and will have to turn the pedals several time to move as many teeth as you would in the big ring. (But it will be easier to turn the pedals since you aren't accomplishing as much.)

In the back the big ring is the easier ring (low gear). As you're pedaling, the number of teeth you turn in the front will cause the same number of teeth to move in the back. If you're in the easier (larger) gear in the back, you'll have to pedal more times (move more teeth) to turn the wheel a whole revolution.

Hope that helps.

[sandy45]

i just want to see if i have this right....in the back...larger ring = low gear which you spin your peddles more to move your bike. and smaller ring = high gear which you dont have to spin that much to move the bike farther.

it is mainly the back that i am worried about. i dont move my front too mcuh for the terrain i am on.

Thanks for all your help!! if i explained it right then i finally understand!